Polymer-Modified MasterSeal (PMM) Ultra

Polymer-Modified MasterSeal (PMM) Ultra Pavement Sealer is an environmentally friendly mineral filled asphalt emulsion pavement sealer blended with polymers and special surfactants for superior adhesion, flexibility and durability. PMM Ultra is a higher solids, faster drying pavement sealer designed to beautify and protect asphalt pavement. PMM Ultra is a ready to apply material that is factory blended with aggregate.

PMM Ultra is ideal for protecting and beautifying all types of pavement surfaces including parking lots, shopping malls, airports, driveways, roadways and more.


One gallon of Polymer-Modified MasterSeal (PMM) Ultra will cover approximately 35-50 square feet per gallon per coat (3.89-5.55 square yards per gallon per coat).

NOTE: Coverage rate may vary due to pavement age, porosity, and method or application.

Surface Preparation

Surface must be clean and free from loose material and dirt. Cracks should be filled with SealMaster Cold or Hot-Applied Crack Filling Materials. Oil stains should be cleaned and primed with SealMaster Oil Spot Primer.

Mixing Procedures

Mix PMM Ultra thoroughly before applying. If needed, a small amount of water may be added to facilitate application.


For optimum performance and durability apply a minimum of two coats of PMM Ultra. A third coat may be applied to high traffic areas such as parking lot entrances, exits and drive lanes for added durability. Allow each coat to dry thoroughly before applying successive coats. Allow final coat to dry for 24 hours prior to opening to vehicle traffic.


Temperatures must be above 50°F both during application and for a period of at least 24 hours after application. Do not apply when rain is imminent or forecast.

Clean Up

Wash tools in water before material dries.


AQUASET is a cold-mix pothole patch that is a permanent repair solution for asphalt and concrete applications. AQUASET is water-activated and uses a proprietary blend of organic additives that are environmentally friendly, safe, and non-toxic. AQUASET is free of solvents and VOC’s. AQUASET is traffic-ready immediately after compaction. AQUASET produces no hydrocarbon leaching or evaporation into the soil or atmosphere, and can be used in all types of weather-cold or warm, wet or dry. AQUASET can be sealcoated after a one hour cure.

Premium, High Performance, Water-Activated Patching Material

• Easy to apply
• Sets up within minutes
• Highly durable
• All weather formula (wet or dry, hot or cold)


One 55 lb. Pail of AquaSet cold patch will cover approximately 5 square feet at 1” depth.


AQUASET is ideal for making rapid permanent repairs on roads, highways, parking lots, bridge decks, driveways, utility cuts and manhole repairs, tennis courts, walkways, and pathways. AQUASET repairs potholes in both asphalt and concrete pavements.

Surface Preparation

Remove all loose material and standing water from area to be repaired. In freezing conditions, all ice must be removed from the area to be patched.

Application Procedures

Fill pothole with AQUASET to a level approximately ½ inch above surface to allow for compaction. Spread evenly with rake or trowel. Prior to compacting, generously sprinkle AQUASET with water so that the water enters the structure and wets the material completely prior to compaction. Compact to a smooth finish with a hand-tamper, vibratory plate or roller. If the compacted material is below the level of the surrounding area, spread more AQUASET, pour more water and re-compact. NOTE- If the depth of the pothole is greater than 3”, it is advisable to fill the pothole in two layers as outlined above.

Clean Up

Use automotive hand cleaners on hands and arms, or vegetable oil based spreads may be used to gently remove material from facial areas.


The cold pothole repair patch with hot mix performance!
Made in Hawaii for Hawaii

  • Made with Hawaiian Basaltic Rock that won’t turn white on the roadway.
  • Easy to Use – Simply pour from bag and tamp or drive over with car wheels.
  • No heating required. A true, cold patch product.
  • PatchMaster can be applied in any weather.
  • Fills potholes in both asphalt and concrete. Ideal for full depth repair.
  • Packaged in 50 lb. weatherproof bags, 1-Ton bags and bulk.
  • Ideal for roads, streets, parking lots, driveways, and other pavement surfaces.


One 50 lb. bag of PatchMaster cold patch will cover approximately 5 square feet at 1″ depth or 2.5 square feet at 2″ depth.

permanent pothole repair

Pothole patching

PatchMaster pothole repair inventory

Driveway repair


PatchMaster is a cold-applied high performance pothole repair material. It is an all-weather material that can be used to fill potholes in wet or dry conditions. PatchMaster remains pliable at temperatures as low as -20°F.


A fast, economical, easy to use pothole repair for parking lots, driveways, roads, streets, and more.

Surface Preparation

Remove loose material, debris, snow, and standing water from pothole prior to application.

Mixing Procedures

Store PatchMaster Pothole Patch in warm area to enhance workability. PatchMaster is a ready to use product. Simply pour or shovel from container.


Apply PatchMaster directly from bag. Fill to a height of 1/2″ above surrounding pavement. Tamp or
compact into place with hand tamper, roller, or car wheels.

Clean Up

Wash tools in water before material dries.

SS-1H Asphalt Binder

SS-1h Asphalt Binder is an anionic asphalt emulsion designed for use as a tack coat for patching, paving, and coating processes. SS-1h Asphalt Binder promotes adhesion of bituminous concrete products and coatings. Meets AASHTO M140, ASTM D977, and the ISSA requirements for SS1h when tested in accordance with ASTM D140, ASTM D244, and ASHTO T59.


  • Tack Coat
  • Fog Seal
  • Prime Coat
  • Slurry Seal
  • Dust Control
  • Base Stabilization


Dependant upon water dilution.


Apply properly mixed SS-1h Asphalt Binder (SS-1h and water) with spray equipment, brush, or squeegee. Stir material thoroughly before applying.


  • For Use as a Tack Coat or Fog Seal: Apply properly diluted SS-1h Asphalt Binder (1 part SS-1h Asphalt Binder, 1 part water) at a rate of .07 – .10 gallon of mix per square yard (90-130 square feet per gallon of mix).
  • For Use as a Primer for Coatings: Apply properly diluted SS-1h Asphalt Binder (1 part SS-1h Asphalt Binder, 8 parts water) at a rate of .07 – .10 gallon per square yard (90-130 square feet per gallon).

Circulation of product is recommended after an extended period of storage.  Avoid repeated pumping.


Apply coatings, patching materials, or paving materials as soon as possible after SS-1h Asphalt Binder dries (within 24 hours) in order to maintain tackifying properties.


Wash tools in water before material dries. After material has dried, clean up with TarBuster or other asphalt remover.